Computation and Design of Detailed Sizing of Stator Slot Types Utilized in Axial Flux Permanent Magnet Machines

Thanh Vu Nguyen, Khoi Trong Nguyen

Abstract


The general electromagnetic design challenge of the axial flux permanent magnet (AFPM) machine includes several critical sections, one of which is the comprehensive design and computation of the stator slot sizing. This is one of the most important aspects of the problem. An algorithm for the precise design of the stator slot sizing is provided in this study. The algorithm is developed by step-by-step calculation analytics. In addition to this, the authors provide formulas that can be used to determine the height of Hs2 for a variety of slot types. The authors of the study make certain recommendations, and one of those recommendations is that the investigation of the flux density on the stator tooth be accomplished through simulation software using the finite element method. This is done so that the authors' recommendations may be proven. The analytic calculation makes the tooth flux density assumption, and the results reveal that the variation from this assumption is not very significant at all. 

Keywords


Stator slot sizing, AFPM, tooth flux density.

Full Text:

PDF

References


Jacek F. Gieras, Rong-Jie Wang and Maarten J. Kamper, Axial Flux Permanent Magnet Brushless Machines. Springer Science, 2008. (Book)

Juha Pyrhonen, Tapani Jokinen and Valeria Hrabovcova, Design of rotating electrical machines. John Wiley & Sons, Ltd, 2014. (Book)

Ziaul Islam, Faisal Khan, Basharat Ullah, Ahmad H. Milyani and Abdullah Ahmed Azhari, " Design and Analysis of Three Phase Axial Flux Permanent Magnet Machine with Different PM Shapes for Electric Vehicles" Energies, MDPI, 2 October 2022, doi: https://doi.org/10.3390/en15207533. (Article)

Zhuo Hao, Yangyang Ma, Pengyu Wang, Geng Luo and Yisong Chen, "A Review of Axial-Flux Permanent-Magnet Motors: Topological Structures, Design, Optimization and Control Techniques" Machines, MDPI, 7 December 2022, doi: https://doi.org/10.3390/machines10121178. (Article)

Ozturk Tosun and Necibe Fusun Oyman Serteller, "The Design of the Outer-Rotor Brushless DC Motor and an Investigation of Motor Axial-Length-to-Pole-Pitch Ratio" Sustainability 2022, 14, 12743, doi: .https://doi.org/10.3390/su141912743. (Article)

Byung-oh tak and Jong-suk ro, "Analysis and Design of an Axial Flux Permanent Magnet Motor for in-Wheel System Using a Novel Analytical Method Combined with a Numerical Method " IEEE Access, Volume 8, November 19, 2020, doi: 10.1109/ACCESS.2020.3036666. (Article)

Werner Jara, Juan A. Tapia, Nicola Bianchi, Juha Pyrhönen, and R. Wallace "Procedure for Fast Electromagnetic Design of Axial Flux Permanent Magnet Machines " International Conference on Electrical Machines. ICEM 2014, 02-05 September 2014, doi: 10.1109/ICELMACH.2014.6960364 (Conference Paper)

Carunaiselvane and Jeevananthan, "Generalized Procedure for BLDC Motor Design and Substantiation in MagNet 7.1.1 Software " International Conference on Computing, Electronics and Electrical Technologies. ICCEET 2012, 21-22 March 2012, doi: 10.1109/ICCEET.2012.6203783 (Conference Paper)

Asko Parviainen, Design of axial-flux permanent-magnet low-speed machines and performance comparison between radial-flux and axial-flux machines, Lappeenranta University of Technology, 2005. (Thesis for the degree of Doctor)

Cogent fully processed non-oriented electrical steels. Cogent Power Ltd at Surahammars Bruks AB in Sweden and Orb Electrical Steels Ltd in the UK. Cogent 2002-11 by SIR-Gruppen Sweden




DOI (PDF): https://doi.org/10.20508/ijrer.v14i1.14327.g8861

Refbacks



Online ISSN: 1309-0127

Publisher: Gazi University

IJRER is cited in SCOPUS, EBSCO, WEB of SCIENCE (Clarivate Analytics);

IJRER has been cited in Emerging Sources Citation Index from 2016 in web of science.

WEB of SCIENCE between 2020-2022; 

h=30,

Average citation per item=5.73

Impact Factor=(1638+1731+1808)/(189+170+221)=9.24

Category Quartile:Q4